Articles

Dumpster Enclosures: What They Are, Sizes, Parts and Cost

Dumpster enclosure guide: what one is, its parts, typical sizes and heights, how it is built and approved, and what it costs, with links to deeper articles.

Use this article to prepare your project questions. Confirm current local requirements with the approving authority and hauler, and confirm product details against the approved project submittal.

Short answer

A dumpster enclosure is a walled or screened area, usually three sides and a pair of gates, that holds a commercial waste container on a concrete pad. It hides the container, keeps litter contained and leaves the collection truck a clear opening. Most are 6 to 8 ft tall, sized to the hauler's containers with about 12 ft of clear gate opening per container.

What is a dumpster enclosure?

A dumpster enclosure is a walled or screened area, usually three sides and a pair of gates, that holds a commercial waste container on a concrete pad. It hides the container from the street and neighbors, keeps litter and wind-blown trash in one place, and leaves the collection truck a clear path to the container. Planners and haulers also call it a trash enclosure, a refuse enclosure or a solid waste enclosure.

Most commercial and multi-family sites need one because the local zoning code requires waste containers to be screened. One city's planning guide quotes its ordinance: containers must be screened from the street by an opaque, durable fence or wall at least 6 ft tall. Rules, sizes and materials differ by city and by hauler. Our guide to dumpster enclosure requirements covers the rules in more depth.

What are the parts of a dumpster enclosure?

A dumpster enclosure has eight working parts: the walls or screen, the posts and their footings, the service gates and their hardware, a pedestrian opening, the concrete pad and apron, container protection, drainage, and the optional roof and lighting. Each one carries a decision that someone on the project team has to make.

PartWhat it doesWhat to decideDeeper article
Walls or screenHides the containers and contains litterMaterial, height, opacity, finish color to suit the buildingSee the build comparison below
Posts and footingsHold the walls and gates against wind and gate loadsPost size, base plates or embedded posts, slab thickening or footings, engineered for the siteWhat to show on enclosure drawings
Service gatesOpen for the hauler, close to screen the containersClear opening per container, leaf count, swing direction, swing angleDumpster enclosure gates and hardware
Gate hardwareHinges carry the leaves; cane bolts (drop rods) pin them; a latch locks them; hold-opens keep them back during serviceHinge type and count, cane bolt sleeves in the slab, a lockable latch, hold-open positionsCovered in the gates article
Pedestrian accessLets staff and tenants drop bags without opening the service gatesA separate pedestrian gate or walk-through opening, and the accessible route to itConfirm with your AHJ
Concrete pad and apronCarries the containers inside and the truck's front wheels outsideThickness, reinforcement, slope, apron sizeDumpster pad and apron design
Bollards or curbsStop containers hitting the back and side wallsBollards or interior curbs, count, offset and heightBollard spacing and placement
DrainageKeeps stormwater out and routes wash water correctlySlab slope, whether a drain is needed and where it connectsCovered in the pad article
Roof and lighting (optional)Keeps rain off stored waste and lights the area at nightWhether a roof is required, clear height for lids, fixture heightWhen cities require a roof

Gates and hardware

A dumpster enclosure with gates has to leave the truck a usable opening. One national hauler's site standard asks for at least 11.5 ft of clear entrance width per container after the gates, poles and hardware are installed, and its drawings show a gate swing of at least 110 degrees with a locking pin hole in the pavement. One city's enclosure guidelines ask for hardware that holds the gates both open and closed, such as a cane bolt with a sleeve in the pavement, and for gates hung on free-standing metal posts set in concrete footings rather than on the block wall.

Pad, apron, protection and drainage

The same city guide calls for at least 4 in of reinforced concrete under the containers, a slab sloped to keep stormwater out (typically 0.5% and no more than 2%), and a reinforced apron at least 10 × 10 ft in front of the gates. The hauler standard asks for two bollards per container, set 1 ft off the back wall and at least 5 ft tall. Enclosure drains, where used, must not connect to the storm drain in that city; wash-water drains at food service sites go to the grease interceptor.

Roof and lighting

A roof is optional unless a local rule requires one. Where one is used, the city guide asks for clearance for the container lid to open, typically at least 8 ft to the lowest fixture, and for adequate lighting around and inside the enclosure.

What are the main ways to build a dumpster enclosure?

There are five common ways to build a dumpster enclosure: site-built CMU block, wood, chain link with privacy slats, vinyl or composite fence kits, and prefabricated or engineered steel systems. The choice comes down to what the local standard accepts, what matches the building, and how hard containers and trucks will use it.

ConstructionHow it is builtWhere it fits
CMU blockContinuous wall footing, block, grout and cap, then steel gates from a separate fabricatorCodes that name masonry; enclosures that must match a masonry building
WoodPosts in individual footings, board-on-board or shadow-box screenLighter-duty sites where the city lists it
Chain link with slatsFence posts in footings, fabric and privacy slatsIndustrial areas; some cities reject it as a wall
Vinyl or compositePanel fence kits on posts in footingsWhere the city lists the product
Engineered steel systemSteel posts on base plates anchored to the slab, steel screen and gates supplied togetherCommercial sites that need opaque, noncombustible screening and a short install

Alpine Citadel is a structural steel dumpster enclosure system: 4 in square steel posts on hot-dip galvanized base plates, 8 in round gate posts, and captive steel slats stacked tight for a 100% opaque face, galvanized and powder coated in any RAL color. There is no continuous wall footing, and most enclosures install in one day on a prepared slab. Bollards, pedestrian gates and covered (steel-roofed) enclosures are available as options. It is accepted in the majority of jurisdictions; where a code names masonry, Alpine provides an alternate-materials submittal with sealed calculations and a building-matched finish. See Alpine's structural steel enclosures for the system, our dumpster enclosure materials comparison for each option in depth, and trash enclosure design ideas for finishes and looks.

How do you build a dumpster enclosure, and who decides what?

You build a commercial dumpster enclosure in a fixed order: confirm the containers with the hauler, read the local standard, lay the enclosure out, choose the construction, detail and engineer it, get approvals, pour the pad and apron, then install the walls and gates.

  1. Containers and service. The owner and the hauler set how many containers, which waste streams (trash, recycling, cardboard, grease) and which collection method. One city's guide advises engaging the hauler early for truck height clearances and maneuvering, and notes that container dimensions vary between hauling companies.
  2. Local standard. Planning or zoning sets location, screening height, materials and color.
  3. Site layout. The architect and civil engineer place the enclosure where the truck can approach straight on, with overhead clearance for the lift. The hauler standard above keeps 24 ft clear over the container.
  4. Drawings. The architect picks the construction and finish and draws the plan, elevations and gate details.
  5. Engineering. A structural engineer designs the walls, posts and foundations for the site's wind loads. For Alpine Citadel, every enclosure is engineered to ASCE 7-22 for its own site, with sealed calculations available in all 50 states.
  6. Approvals. Zoning review, and a building permit where required. The model building code exempts fences not over 7 ft from a building permit (2024 IBC Section 105.2), but many cities still require one for enclosures, and taller or roofed enclosures usually need one.
  7. Pad and apron. The general contractor pours the slab, apron and any thickened areas at posts to the civil and structural details.
  8. Walls and gates. The installer sets the walls and hangs the gates, then the gates are checked for clear opening, swing and pinning before the hauler's first pickup.

How big should a dumpster enclosure be?

A dumpster enclosure should be sized around the hauler's containers, the clearances around them and the clear gate opening, not the container's capacity alone. Published standards for one front-load container commonly ask for about 10 × 10 ft to 12 × 11 ft inside, and two containers need roughly 20 to 23 ft of width.

  • One city's planning guide lists 10 × 10 ft for one 6 or 8 cubic yard dumpster, 10 × 15 ft for one dumpster plus carts, and 10 × 20 ft for two.
  • The hauler standard asks for at least 12 ft wide by 11 ft deep inside for one container and 23 × 11 ft for two, with 2.5 ft of clearance at the sides and 2 ft front to back.

Alpine publishes two example configurations so buyers can compare: a nominal 12 × 16 ft single (16 ft 8 in × 12 ft 2 in inside, one 12 ft clear gate, room for a container plus carts) and a nominal 24 × 12 ft double (26 ft 2 in × 12 ft 2 in inside, two 12 ft clear gates on a center post). Every enclosure is laid out to its site, and any size can be built. Our dumpster enclosure dimensions guide walks through sizing by container and gate.

How tall is a dumpster enclosure?

Most dumpster enclosures are 6 to 8 ft tall. The height is set by the local code and has to be tall enough to hide the container, including its lids.

  • 6 ft is a common minimum: one city's ordinance requires an opaque screen at least 6 ft tall, and another city's guide calls 6 ft its standard wall height.
  • The national hauler standard above asks for walls at least 7 ft tall, and the town that publishes it adds its own 8 ft minimum.
  • Height also drives permitting: fences over 7 ft fall outside the model code's building permit exemption, so 8 ft enclosures usually need a permit.

Alpine Citadel's standard heights are 6, 7 and 8 ft, and enclosures are built from 5 ft to 10 ft with engineering for the site.

How much does a dumpster enclosure cost?

An 8 ft Alpine Citadel single typically costs $15,000–20,000 installed, excluding slab and site work, while 2025 public bids priced complete single enclosures at $20,000–30,000 including site concrete. Construction, size, height, gates and how much concrete is in the scope move the number, so compare quotes on the same scope.

Typical installed cost for an 8 ft Alpine Citadel enclosure, excluding slab and site work, is $15,000–20,000 for the nominal 12 × 16 ft single and $21,000–30,000 for the nominal 24 × 12 ft double, including the engineering package for the example configurations. Alpine Citadel costs less than a comparable CMU enclosure: 2025 public bids priced complete single enclosures at $20,000–30,000, including site concrete (a school district's April 2025 bid tabulation and a town's June 2025 bid documents, where the CMU walls alone were quoted at $9,850). Those bids include site concrete and Alpine's range does not, so add your slab and site work before comparing. Design, approvals, fabrication, delivery and concrete work are additional to the one-day install. Program pricing for multi-site rollouts is available on request. The full breakdown is in our article on what a dumpster enclosure costs.

What should multi-site and national program buyers standardize?

A brand building enclosures across many sites should standardize one engineered detail that passes most local standards, then adapt only the size, height and color per site. A prototype detail in wood, vinyl or slatted chain link will be rejected in part of any national footprint.

  • One primary detail in an opaque, noncombustible material, with the finish tied to the building palette.
  • Set container counts and clear gate openings with the national hauler accounts, and keep a shared-wall double for sites that store two streams, such as trash and tires.
  • A standard submittal package for cities whose code names masonry but allows alternates.

Alpine has 70+ locations installed, including 60+ for a multi-state tire and automotive service brand. Each site gets its own engineering package in under one week, each enclosure ships as one kit with parts tagged by bay, and kits can be organized by site and release. Our guide to a trash enclosure standard for a multi-site rollout covers the program side.

Next step

If you are planning an enclosure, send the site plan, the city's enclosure standard, the hauler's container sizes and the height you need. Alpine will lay out the enclosure, confirm the clear gate openings and price the same scope you are comparing. Request a quote.

Sources

Frequently asked questions

Is a dumpster enclosure the same as a trash enclosure?

Yes. Dumpster enclosure, trash enclosure, refuse enclosure and solid waste enclosure all describe the same thing: a screened, gated area for commercial waste and recycling containers. City codes and hauler standards use whichever term is local, so search for all of them when you look up your city's rules.

Do dumpster enclosures need to be accessible?

Where tenants or staff walk to the containers, accessibility rules can apply to the route and the pedestrian opening. One city's guide points designers to its building code's accessibility requirements and recommends a pedestrian gate separate from the service gates. Confirm what applies with your AHJ.

Does a dumpster enclosure need a floor drain?

Usually not. Most standards slope the pad so stormwater runs out rather than in. A drain is mainly a food service question, where wash water has to reach a grease interceptor, and at least one city bars any enclosure drain from the storm drain. Your civil engineer and the local standard decide.

Which CSI section covers a dumpster enclosure?

MasterFormat has no section named for dumpster enclosures. An engineered steel slat enclosure with gates fits best under 32 31 19, Decorative Metal Fences and Gates. A CMU enclosure belongs in 04 22 00, Concrete Unit Masonry, with its steel gates specified separately.

How long does it take to install a dumpster enclosure?

For Alpine Citadel, most enclosures install in one day on a prepared slab. Design, approvals, fabrication, delivery and concrete work are additional, so plan the schedule from the date the layout is approved, not from the install day. CMU enclosures take longer because footing, block, grout and cap are built in sequence.

Your project

Plan your enclosure with Alpine

Share your project location, site plan and access requirements. We’ll review the layout, engineering and quotation scope with your team.